BV600 - DSC Dual PIR Motion
 |
The Bravo 6 will ignore a full range of false alarm sources (including pets up to 85lbs) without compromising exceptional intruder catch. Bravo 6 features HDD, a dual element detection system so advanced it's covered by two patents and so intuitive Bravo 6 is a snap to install. Say goodbye to pet alley masking and range adjustments. 40'L X 50'W Coverage Area. |
|
FEATURES
¡¤ |
Multi-level PIR signal processing? |
¡¤ |
Single/dual element low noise sensor |
¡¤ |
High level static and transient protection |
¡¤ |
Exceptional white light immunity |
¡¤ |
Excellent RF immunity |
¡¤ |
Temperature compensation |
¡¤ |
LED on/off jumper |
¡¤ |
Vertical adjustment |
¡¤ |
Super quiet operation |
¡¤ |
Wall, corner, or ceiling mounting |
¡¤ |
Attractive styling for any decor |
| ¡¤ |
5 year warranty |
| ¡¤ |
Dual PIR sensors with High Density Digital Analysis* and multi level signal processing for better intruder catch and immunity to pets weighing up to 85lbs/38kg |
¡¤ |
Digital temperature compensation |
MODELS
| BV-600 |
Form A alarm contact |
| BV-601 |
Form A alarm contact & tamper switch |
| BV-602 |
Form C alarm contact & tamper switch |
LENS COVERAGE
Dual PIR lens pattern.... |
40'L x 50'W (12.2 x 15.2 m) |
SPECIFICATIONS
Operational :
| Mounting height............ |
6' to 10' (2 to 3m) |
Lens horizontal
pattern angle................. |
100° minimum |
| Vertical adjustment....... |
from +5° to -10° |
| Alarm duration............. |
2 to 3 seconds |
| Walk speed.................. |
0.5 to 10 ft/s
(0.15 to 3.0 m/s) |
Environmental/Immunity :
| Operating humidity....... |
5% to 95% non-condensing |
| RF/EMI immunity......... |
10V/m 80% A.M.,
from 80 to 1,000 MHz |
| Transient immunity....... |
2.4kV @ 1.2 joules |
| Static immunity............. |
15kV |
| White light immunity..... |
4kLux |
| Operating temperature.. |
32° to 122°F (0° to 50°C) |
Electrical :
| Operating voltage........ |
9.5 to 14.5VDC |
| Ripple tolerance.......... |
3Vpp at 12VDC |
| Standby current........... |
17.5mA at 12VDC |
| Alarm current.............. |
25mA at 12VDC |
| Contact ratings............ |
100mA at 24VDC |
| Alarm contact series resistance.................... |
10ohm 0.25W |
Physical :
| Dimensions................. |
4.9"H x 2.76"W x 1.75"D
(12.5 x 7.0 x 4.5cm) |
| Mounting.................... |
wall or corner |
| Color.......................... |
designer white, with light grey lens |
(For clarity, overlapping beams are not shown)
¡¡
¡¡ |
PIR 1 - Top Lens |
| ¡¡ |
PIR 2 - Bottom Lens |
Multi-level signal processing with a vertically interleaving beam pattern |
Architect's Specifications
The contractor shall provide infra-red motion detectors in the areas specified on the drawings. Contractor shall be responsible for determining the best mounting location in each area to provide full coverage while minimizing false alarms. Wall mount detectors shall in addition be ceiling, or corner mountable, and shall share common mounting brackets so that they are interchangeable. Mounting position shall be adjustable both vertically and horizontally so that final position may be fine tuned as required during walk-testing.
Detectors shall employ multi-level signal processing and temperature compensation for accurate detection, even in warm environments? They shall have high immunity to false alarms from RF, static, electrical transients, and white light.
All detectors shall carry a 5 year manufacturer’s warranty.
Motion detectors for each area shall be selected from the following to best match the coverage requirements of each area :
Bravo6
For areas where maximum immunity to false alarms caused by pets is required, without a reduction in the ability to detect people, detectors shall have dual PIR sensors employing high density digital analysis and multi-level signal processing with a vertically interleaving beam pattern. Detector shall provide 40' L x 50' W (12.2 x 15.2m) wall to wall coverage.
|
