Ultra-small wirefree curtain PIR detector
Clip MCW is the industry's smallest and most elegant wireless curtain-type PIR detector designed for the protection of doors, windows and all-glass walls. This fully-supervised detector featuring anti-collision PowerCode(TM) technology is compatible with the PowerMax(R) wireless family and other Visonic PowerCode(TM) wireless receivers.
Clip MCW creates a protective curtain enabling complete coverage for properties with large or subdivided windows, doors and all-glass walls. Clip MCW provides full perimeter protection while allowing consumers to normally and freely use the premises without triggering a false alarm.
Clip MCW uses advanced patented digital FM signal processing, as well as the well-known patented TMR(TM) algorithm to enable three different detection modes (2m, 4m, 6m) in a single detector, each programmable for optimal performance with the unit's specific application. Advanced motion analysis enables Clip MCW to distinguish human motion from other disturbances for the most accurate detection and the fewest false alarms.
The Clip MCW is available in several optional frequencies in compliance with European, U.S. and other international standards.
Clip MCW Features
- A fully-supervised wireless curtain-type detector with anti-collision PowerCode(TM) technology
- Compatibility with members of the PowerMax(R) family and all Visonic PowerCode(TM) wireless panels and receivers
- Fast and easy installation
- Digital FM technology incorporating an advanced selector (2m, 4m and 6m) for optimized detection and false alarm processing
- Ultimate false alarm elimination via patented TMR(TM)algorithm
- 3-volt long-life high power standard lithium battery
- Attractive, sleek design suitable for any home or office
- Several optional frequencies available in compliance with international standards
|Part Number||CLIP MCW|
|What's in the box||(1) Visonic CLIP MCW Ultra Small Wireless Curtain PIR Detector|
Write Your Own Review
|Detector Type||Dual-element low noise pyroelectric sensor|
|Number of Curtain Beams||2|
|Mounting Positions||See Figures 2 through 6|
|Range Settings||Long (6 m), Medium (4 m) and Short (1.2 - 2m) (Jumper-selected)|
|Internal Battery||3V Lithium battery, type CR123A. For UL installations, use Panasonic or Sanyo only|
|Nominal Battery Capacity||1450 mA/h|
|Battery Life (with LED on)||3 years (for typical use)|
|Battery Power Test||Performed immediately upon battery insertion and periodically every several hours|
|Microprocessor||8-bit, low power CMOS|
|Visual Indications||LED Lights for about 3 seconds upon transmission of alarm & tamper messages and upon motion detection in the walk test mode.
LED Flashes during the power-up stabilization period (approx. 2 min), or after restoring the cover (by pressing the tamper switch).
LED Does not light upon transmission of supervision messages
|Alarm Period||Approx. 3 seconds|
|Rearm Timer||Rearms the detector 2 minutes after the last alarm|
|Frequency (MHz)||315 (U.S. version), 433.92, 868.95, 869.2625 or other frequency according to local requirements|
|Transmission Sequence||3 data bursts at variable intervals within 3 seconds|
|Encoding||24-bit ID, over 16 million possible combinations|
|Total Message Length||36 bits|
|Tamper Alert||Reported when a tamper event occurs and in any subsequent message, until the tamper switch is restored|
|Supervision Message||Signaling at 60-minute intervals (U.S. version), 15 minute intervals (UK version), or according to the local standards|
|Height||1.8 - 2.4 m (6 - 8 ft)|
|Installation Options||See Figures 9 through 13|
|Operating Temperature||-10°C to 50°C (14°F to 122°F)|
|Storage Temperature||-20°C to 60°C (-4°F to 140°F)|
|RFI Protection||> 20 V/m to 1000 MHz|
|Compliance with Standards||Directive 1999/5/EC of the European Parliament. EN 50131-2, Grade 2, Class II 2 DE3594|
|Dimensions (H x W x D)||105 x 35 x 30 mm (4-1/8 x 1-3/8 x 1-3/16 in.)|
|Weight (with battery)||60 g (2.1 oz)|
|U.S. Patent||5,693,943 (other patents pending)|